River City Volkswagen Club  
Home •  Club Meetings •  Gatherings •  Car Pics •  Links •  Message Board
FAQ •  Search •  Memberlist •  Calendar •  Album
Register •  Profile •  Log in to check your private messages •  Log in
 
upper torsion arms binding - suggestions?

 
Post new topic   Reply to topic    River City Volkswagen Club Forum Index -> General Chatter
View previous topic :: View next topic  
Author Message
robl245



Joined: 05 Jun 2008
Posts: 31
Location: Athol, ID

PostPosted: Fri Apr 24, 2009 7:57 am    Post subject: upper torsion arms binding - suggestions? Reply with quote

I've just installed a used narrowed (2 in) beam with sway-a-way style adjusters in my 71 standard bug. I have a wanted add looking for a stock beam, but I'm still not quite ready to give up on this one quite yet. The lower torsion arms move up and down nice and freely (I mean nice and springy). The uppers seem to be binding. I pulled the drivers side out, cleaned it up, regreased and reinstalled it. It still doesn't move as easily as the bottom, but it's probably acceptable. The passenger side though is stuck fast when pushed back in all the way. I can move it up and down if I really reaf on it.

Anybody ever experience this? Causes? Could the top tube be bent?

When it first catches the spring it's fine, but when shoved in that last inch or two, it's a super tight fit. It's greased up nice. It's hard to look down the tube with the spring in there.

Any suggestions?

Thanks everyone.


Last edited by robl245 on Fri Apr 24, 2009 1:24 pm; edited 1 time in total
Back to top
robl245



Joined: 05 Jun 2008
Posts: 31
Location: Athol, ID

PostPosted: Fri Apr 24, 2009 10:56 am    Post subject: Reply with quote

Just thinking out loud..... What if I clean things out in the offending end of the beam tube and run a hone through there? (one of these: http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=97163

Good / Bad idea?

[EDIT] After looking at a front end diagram, I now see that there is some sort of bushing in there. So, the hone is probably a bad idea. Maybe a messed up inner bushing then? Are there inner bearings also (in addition to the ones in the ends)?
Back to top
CustomVW



Joined: 13 Oct 2006
Posts: 323
Location: Hillyard off market st. and gordon

PostPosted: Fri Apr 24, 2009 2:11 pm    Post subject: Reply with quote

I would suspect the bearing in the end of the tube has failed.
Back to top
Bad Bug Two



Joined: 23 Feb 2007
Posts: 94
Location: Spokane, WA

PostPosted: Sun Apr 26, 2009 5:34 am    Post subject: Reply with quote

There should be a roller bearing on the outer most part of the tube and a bushing inside. The only time I have ever run into this same problem I ended up carefully honing the inside bushing. I removed all of the torsion leaves, honed it a little at a time until the trailing arm moved as I wanted and then cleaned it up, regreased and reassembled it.

While it was apart, I checked all four, just to make sure the moved smoothly without the springs inside. This was a brand new beam that I was putting in a car, so they must have made a mistake on the new bushing.

Good luck!

Cool

_________________
Jeff Rogers
www.badbugracing.com
9.35 @ 145
Back to top
CustomVW



Joined: 13 Oct 2006
Posts: 323
Location: Hillyard off market st. and gordon

PostPosted: Sun Apr 26, 2009 4:08 pm    Post subject: Reply with quote

mkae sure, when repairing it, to check the hardened surface on the torsion arm.
Back to top
Display posts from previous:   
Post new topic   Reply to topic    River City Volkswagen Club Forum Index -> General Chatter All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


© River City Volkswagen Club, Powered by phpBB
Site Design and Hosting provided by Polestar Internet Services